Skiing/Snowboarding
A ski is a long flat device worn on the feet designed to help the wearer slide smoothly over snow. Originally intended as an aid to travel in snowy regions, they are now primarily used for recreational and sporting purposes. Also, a ski may denote a similar device used for other purposes than skiing, for example, for steering snowmobiles.
Snow skis glide on snow because downward pressure, as well as heat from surface friction, melts a thin layer of snow directly under the ski. This creates a very thin layer of water directly under the ski upon which the ski glides. Ski wax is used to decrease drag by increasing the water repellent properties of the base.
Snowboards are constructed of a hardwood core and laminated with Glass-reinforced plastic fiberglass. The nose or "front" of the board is upturned, to help the board glide over uneven snow; the tail or "back" of the board is also upturned to enable switch or "backwards" riding. The base (the side of the board that touches the snow) is covered with a plastic called p-tex, which is typically sintered to help it absorb wax, which helps it slide faster. The edges of the base are fitted with a steel edge, just a couple of millimeters square, which helps the board grab the snow when turning. The top of the board typically sports graphics designed by board makers to attract riders to their boards or to display artwork. Flite Snowboards, an early and often underquoted designer, pressed the first closed-molded boards from a garage in Newport, RI in the mid-80's, well before Burton did it. Snowboard topsheet graphics can be a highly personal statement and many riders spend many hours customizing the look of their boards. The base of the board may also feature graphics, often designed to make the manufacturer recognisable in photos.
See also: Board Construction
Snowboard designs differ primarily in:
* Length - Boards for children are as short as 90 centimetres; boards for racers, or "alpine" riders, are as long as 215 cm. Most people ride boards in the 140-165 cm range. It is a myth that the height of the rider solely dictates the length of the snowboard. Rather, the length of a snowboard corresponds mainly to the style, weight, and preference of the rider. A good rule of thumb is to stay within the recommended manufacturer weight range. The longer the board, the more stable it is at high speed, but it is also a bit tougher to maneuver. Another factor riders consider when selecting a snowboard is the type of riding it will be used for, freestyle boards being shorter than all-mountain boards.
* Width - The width is typically measured at the waist of the board, since the nose and tail width varies with the sidecut and taper. Freestyle boards are up to 28 cm wide, to assist with balance. Alpine boards are typically 18-21 cm wide, although they can be as narrow as 15 cm. Most folks ride boards in the 24-25 cm range. Riders with larger feet (US size 10+) may have problems with narrower boards, as they have substantially less surface area along the edges. As a result, a rider's toes and/or heels may extend over the edge of the board, and interfere with the board's ability to make turns once it is set on edge, or 'get hung up on the snow.' This is called toe/heel-drag, and can be cured by either choosing a wider board (26cm or more), adjusting the stance angle, or a combination of the two.
* Sidecut - The edges of the board are symmetrically curved concavely, so that the width at the tip and tail is greater than the center. This curve aids turning and affects the board's handling. The curve has a radius that might be a short as 5 meters on a child's board or as large as 17 meters on a racer's board. Most boards use a sidecut radius between 8-9 meters. Shorter sidecut radii (tighter turns) are generally used for halfpipe riding while longer sidecut radii (wider turns) are used for freeride/alpine/racing riding. One new development in sidecuts was the introduction of Magne-Traction by Mervin, which owns: Lib Tech, GNU, and Roxy. Magne-Traction incorporates seven bumps on each side of the board which LibTech speculates will improve edge holding.
* Flex - The flexibility of a snowboard affects its handling and typically varies with the rider's weight. Usually a softer flex makes turning harder while a harder flex makes the board less stable at high speed. There is no standard way to quantify snowboard stiffness, but novices and boarders who mostly do rails tend to prefer softer flex, racers stiffer flex, and everyone else something in between.
* Tail/nose width - Many freestyle boards have equal nose/tail specs for equal performance either direction. Freeride and alpine boards, however, have a directional shape with a wider and longer nose. Boards designed for powder conditions exaggerate the differences even more for more flotation on the powder.